YSKG 1200X2800 four coloration flexo printing &rotary die slicing equipment
.Use and functionality
1.The total machine electrical appliances adopt renowned manufacturer.
2.The transmission equipment of the equipment adopts 40Gr to be quenched and tempered.
three.All axes are taken care of with chromium plating to increase the surface area hardness.
four.The equipment undertake round spray lubrication generate.
five.The host adopt frequency conversion handle.
six.Module layout, any mix of multicolor printing unit.
.Main mechanical features configuration and technological parameters
Paper feeding department
A.Entrance edge feeding program.(Can also be geared up with gentle force, or stress free of charge entrance paper feeding mechanism)
- Three axis entrance feed, boost the flow of enthusiasts, to sustain higher velocity, lower velocity paper feeding precision, the smallest paper width 350mm.
- Modify the air circulation and pressure in four sections to match the dimension of the board.
- Positioning by the front baffle to reduce feed mistakes, increase paper feeding, printing and die-reducing precision.
- CZPT handle of still left and correct baffle.
- CZPT control of rear supporting board.
- Front paper baffle clearance altered by guide.
- Equiped with continuous and intermittent paper feeding perform. (optional or ongoing feed) as essential.
B.Higher and decrease roll
- Upper roller:The outdoors diameter is 155mm,use resistant rubber on the surface area of steel pipe.
- Reduced roller: the outer diameter of the 155mm paper feeding roller floor embossed plated challenging.
- Feeding force roller adjustment hole handbook adjustment, adjustment assortment -12mm.
- The energy transmission of the stress roller is pushed by the rolling cross coupling, which minimizes the abrasion and helps make the transmission a lot more balanced.
- Device clutch, accompanied by sirens, proceed to ring the alarm when traveling, to make sure the basic safety of operators.
- The driving shaft is presented with a friction type clutch to keep away from the misoperation and injury to the equipment.
- The primary motor is outfitted with protection gadget (not commence device locking when the host is unable to switch the shipment).
- Paper feeding device electrical automated zeroing.
- The common carton use automated zeroing gadget, consider printing 1 to 2 pieces of cardboard can be altered to the right place, lessen cardboard squander.
Printing division
A.Printing roller
- The outer diameter is 395.6mm (with diameter of 410mm).
- Higher top quality metal, area grinding, difficult chromium plating.
- Scroll hanging model, using the appropriate and left sides of the locking unit, so that the far more accurate model of the hanging.
- Total variation of hanging plate hook, undertake 9mm hanging bar.
- Loading and unloading printing board, foot switch electric powered handle CZPT and reverse.
B.Printing push roller
- The outdoors diameter is 155mm
- Steel pipe floor grinding, tough chromium plating.
- The strain roller gap is adjusted manually, and the adjustment variety is -12mm.
C.The metallic roller (CZPT according to customer need for the mesh) (high with 250 mesh ,optional ceramic roller)
- The outdoors diameter is 215mm.
- The surface of the metal pipe is manufactured of superior chromium plating process.
- Dot regular, ink uniform.
- Extend the service daily life of printing plate and rubber roller.
- The anilox roller clearance is adjusted manually, and the adjustment variety is -12mm.
D.Rubber roller
- Uniform ink roller, coated with dress in-resistant rubber, rubber roller large parabolic kind, to compensate for the power deformation, improve the influence of inking. Rubber for the butyl rubber, shore hardness of sixty degrees or far more, by means of the particular result of good polish ink. The rubber roller is driven by the motor when the equipment is stopped.
two.The outside diameter is 205mm
three.The rubber roller clearance is altered manually, and the adjustment variety is -12mm.
E.Phase adjusting mechanism
- Planetary equipment construction.
- The printing period is managed by computer and electric electronic management (360 degrees)
- The transverse route of the printing roller is modified manually, and the adjustment assortment is 5mm.
- The printing plate roller utilizes the electric adjustment phase, to return to zero and the version velocity is fast, adjusts the edition precision to be high.
F.Paper feeding roller
1.Paper feeding upper roller, outer diameter of 86mm, large good quality metal plated difficult chromium with 4 guidebook wheel diameter of 125mm.
2.Paper feeding reduced roller, outer diameter is 155mm, guide paper roll plating challenging chromium.
three.The manual roll hole is adjusted manually, and the adjustment selection is -12mm.
G.Ink circulation structure
- Pneumatic diaphragm pump for ink stability, basic operation and servicing.
- Ink filter,Filter impurities
H. Printing roller repairing device
- Adopt pneumatic brake system. When the device is employed for separating and altering the phase or cleansing, the brake mechanism limitations the equipment to rotate, and the fastened placement of the unique gear placement is managed.
- The electricity transmission of the strain roller is pushed by the rolling cross coupling, which reduces the abrasion and makes the transmission more steady.
Slotting department
1.The outer diameter of the cutter shaft is 156mm, the outer diameter of the cutter shaft is 156mm, and the area is plated with hard chromium.
two.Push line wheel clearance handbook adjustment.
3.Width of slotting cutter 7mm. Alloy steel materials.
four.Slotting knife seat clearance worm gear box adjustment, dial screen, adjustment selection – 10 mm.
5.Planetary equipment framework for slotting period adjustment
six.Slotted section making use of the period controller digital 360 degree adjustment (run, quit can be adjusted)
seven.Guide synchronization modify box top.
8.The best and bottom rollers of the strain line are one hundred ten mm, which is created of higher top quality thick wall seamless metal tube, and the surface is hard to be plated with hard chromium. The wire diameter phi 176.
Die slicing department
A. Rubber pad roller
one.The outer diameter of the rubber pad roller is 388.9mm.
two.Rubber pad roller for large good quality steel, area grinding, challenging chromium plating.
3.Rubber pad thickness 8mm, width 250mm.
four.The adjustment of the hole in between the pad roller and the cutter roller adopts guide adjustment, and the adjustment assortment is -16mm.
5.Automated payment construction of rubber pad roller, automatic control of pad roll velocity.
six.Rubber pad roll slicing flat construction, maintain the pad roll.
7.The rubber pad roller adopts the 1:900 motor crankshaft rotation conversion to 30mm swimming transverse framework.
B.Die reducing roller
- Die roll 360mm.
- The die roller is of high good quality steel, the surface area is grinded, difficult chromium plating.
- Dynamic stability correction, increased functioning balance.
- Die fastened screw gap spacing, horizontal 100mm, radial twelve, screw hole M10.
- Software of line height 22.60mm
- Wood template thickness 13mm, blade height twenty five.4mm.
- The cutter roller adopts handbook adjustment, the adjustment range is 10mm
C.Die cutting section altering mechanism planetary gear kind composition.
- Die slicing phase using the pc and electrical digital management 360 diploma adjustment (operate, stop can be modified).
- Push line wheel clearance guide adjustment, modify the scope of 1-12mm, employing the cross slider system, adjust the transmission equipment always make sure the right meshing point out.
- Bottom cutter makes use of the intercontinental brand rubber pad.
.CZPT parameter
| Machine dimensions | MM | 1200X2800 | |
| 1 | Machine internal width | MM | 2900 |
| 2 | Max paper dimension | MM | 1200X2700(Ongoing paper) |
| three | Min paper measurement | MM | 400*600 |
| 4 | Max printing region | MM | 1150X2500 |
| Max slotting region | MM | 1150X2500 | |
| Min slotting size | MM | 380 | |
| five | Min die cutting dimensions | MM | 380 |
| six | Max die slicing region | MM | 1150X2500 |
| 7 | Printng roller and die cutter roller traverse | MM | ten both still left and right |
| eight | anilox roll guide adjustment higher and decrease | MM | ~eleven |
| 9 | Reduced printing roll handbook adjustment upper and reduced | MM | ~eleven |
| 10 | Rubber roller automatic traverse | MM | twenty each still left and proper |
| eleven | Printing roller, rotary die reducing roller, rubber roller physique ratation | degree | 360 |
| 12 | Economic pace | P/min | 120 |
| 13 | Feeding rubber roller | Φ | 156 |
| fourteen | Printing roller diameter | Φ | 410(include printing plate) |
| 15 | Wall of device | HT200 | 50MMthickness |
| sixteen | Driving equipment | 20GrMnTi | Hardness 60, fantastic grinding, transmission gear thickness 50mm |
| 17 | Paper feeding precision | ±1.0mm | |
| 18 | Die cutting precision | ±1.0mm | |
| 19 | Main motor power | 15KW | |
| twenty | Production electrical power | 26KW | |
| 21 | Total electrical power | 33KW |
.Principal elements first place
Name Brand
- CZPTs Qianchaowanxiang,HangCZPT
- AC contactor, thermal relay chint
3,Keyless connection ring HangCZPT
four,Pneumatic diaphragm pump HangCZPTang
5,Frequency converter Puchuan
six,Pneumatic solenoid directional valve chint
7,Pneumatic cylinder chint
8Metal Anilox Roller HangCZPT junfeng
9Printing rubber roller ZheJiang HangCZPT
- knife imported
- Rubber Chaonai,Ledika
Corrugated printer Carton flexo printing slotting machine
1 Whole machine electric elements was option the domestic popular manufacturer, good high quality and steady.
2 Complete equipment baffle and important elements utilised the temper for decrease the steel interior power and that areas are produced by higher precision processing heart and grinded by digit managed grinder.
3 All the transmission axles and rollers are created by large-high quality steel, and processed by means of mood and dynamic equilibrium plated with rigid chrome and grinded area.
4 All the transmission gears was utilised the forty five# alloy metal, which is grinded following warmth-therapy, and it was created by rubbing, it nonetheless maintains the substantial topping precision.
5 The complete device undergoes the spray lubrication, intuitionist demonstrate placing, placing the double oil pipe equilibrium program.
6 Option: Presetting adjustment purpose, feeding, printing, slotting, zero environment, memory reposition automated.
7 Whole device operating interval adjustment, self-lock worm wheel and worm system, quick and convenient.
8 Option the vacuum adsorption, kick feeding or guide edge feeding to the client request.
Selection: Anilox roller, And stacker Equipment.
CZPT Parameter:
| YFQ480×1800 | 1447×2000 | 1447×1800 | -60 Piece/min | 5.5kw |
| YFQ480×2000 | 1447×2200 | 1447×2000 | -sixty Piece/min | 5.5kw |
| YFQ480×2400 | 1447×2600 | 1447×2400 | -sixty Piece/min | 5.5kw |
| YFQ480×2600 | 1447×2800 | 1447×2600 | -sixty Piece/min | five.5kw |
CZPTer check out:
Shipping and delivery photos:
Carton box photos:
Factory procedure:
Related Products:
Welcome to contact us for far more information and films
Carina
Internet site: http://
Fax/tel: 0571 -7805687
